DeskProto user forum

Forum: communicate with other users

Forum home page	main
Forum:	General

You’re logged in as:	guest
Online users:	0
Online guests:	34

page 1 of 75

Thread Title	Replies	Views	Last post
Possible data leak: new passwords needed ! started by: Lex created: 2020-11-24	0	4371	2020-11-24 10:00 CET by: Lex

Before you join in, please read the forum rules ! started by: Lex created: 2006-10-03	0	89211	2006-10-03 20:12 CEST by: Lex

Geometry-only want the outside machined started by: parchping created: 2026-04-15	3	38	2026-04-16 14:49 CEST by: parchping

Issue with ball bit digging deeper in certain area started by: jgutier3 created: 2026-04-12	3	65	2026-04-13 14:51 CEST by: jgutier3

Rest Machining? started by: Dylan created: 2024-12-04	3	202	2026-04-07 20:48 CEST by: Lex

Moving to Deskproto trying to understand the softw started by: Fermate created: 2026-03-24	3	76	2026-03-25 14:43 CET by: Lex

machining with 4th axis (B) started by: Kris10x created: 2026-03-24	1	52	2026-03-24 14:13 CET by: Lex

tangentical Knife Setup started by: AVAK created: 2026-03-16	1	54	2026-03-17 09:09 CET by: Lex

Index cut clearance started by: Hitime created: 2026-03-13	5	68	2026-03-16 15:39 CET by: Lex

erreur d échelle started by: mertens.l created: 2026-03-10	3	44	2026-03-10 13:55 CET by: mertens.l

change the degree of A axes started by: Steven created: 2026-02-09	10	286	2026-03-10 12:17 CET by: Lex

Cutter Diameter Question started by: hoyt created: 2026-02-15	16	292	2026-03-06 20:09 CET by: hoyt

Cavera Air 4th Axis Tailstock started by: Mitch created: 2026-03-06	2	61	2026-03-06 11:26 CET by: Mitch

4th Axis toolpath started by: Mitch created: 2026-02-28	3	120	2026-03-06 10:04 CET by: Lex

Ball end mill - 4th axis settings started by: Mitch created: 2026-03-05	1	62	2026-03-06 08:53 CET by: Mitch

Object and material diameters started by: Hitime created: 2026-03-04	1	51	2026-03-04 21:32 CET by: Lex

Mamimum Spindle RPM started by: bce.gatien created: 2026-03-01	1	72	2026-03-02 12:06 CET by: Lex

Venus started by: gap23 created: 2026-02-21	2	96	2026-02-27 02:28 CET by: gap23

New Feature Request started by: hoyt created: 2026-02-07	5	211	2026-02-26 13:40 CET by: Lex

Exporting as .tap, .nc started by: MarkNotts created: 2026-02-26	2	50	2026-02-26 09:27 CET by: MarkNotts

page 1 of 75